Settings.Secure

If accessibility is enabled.

Whether to speak passwords while in accessibility mode.

Whether ADB is enabled.

Origins for which browsers should allow geolocation by default. The value is a space-separated list of origins.

Setting to allow mock locations and location provider status to be injected into the LocationManager service for testing purposes during application development. These locations and status values override actual location and status information generated by network, gps, or other location providers.

A 64-bit number (as a hex string) that is randomly generated on the device's first boot and should remain constant for the lifetime of the device. (The value may change if a factory reset is performed on the device.)

Whether background data usage is allowed by the user. See ConnectivityManager for more info.

Whether bluetooth is enabled/disabled 0=disabled. 1=enabled.

Whether or not data roaming is enabled. (0 = false, 1 = true)

Setting to record the input method used by default, holding the ID of the desired method.

Whether user has enabled development settings.

Whether the device has been provisioned (0 = false, 1 = true)

List of the enabled accessibility providers.

List of input methods that are currently enabled. This is a string containing the IDs of all enabled input methods, each ID separated by ':'.

Host name and port for global http proxy. Uses ':' seperator for between host and port TODO - deprecate in favor of global_http_proxy_host, etc

Setting to record the visibility of input method selector

Whether the package installer should allow installation of apps downloaded from sources other than Google Play. 1 = allow installing from other sources 0 = only allow installing from Google Play

Comma-separated list of location providers that activities may access.

Whether autolock is enabled (0 = false, 1 = true)

Whether lock pattern will vibrate as user enters (0 = false, 1 = true)

Whether lock pattern is visible as user enters (0 = false, 1 = true)

The Logging ID (a unique 64-bit value) as a hex string. Used as a pseudonymous identifier for logging.

User preference for which network(s) should be used. Only the connectivity service should touch this.

No longer supported.

No longer supported.

No longer supported.

Setting to record the input method subtype used by default, holding the ID of the desired method.

Settings classname to launch when Settings is clicked from All Applications. Needed because of user testing between the old and new Settings apps.

If touch exploration is enabled.

Default text-to-speech country.

Default text-to-speech language.

Default text-to-speech engine pitch. 100 = 1x

Default text-to-speech engine speech rate. 100 = 1x

Default text-to-speech engine.

Default text-to-speech locale variant.

Space delimited list of plugin packages that are enabled.

Setting to always use the default text-to-speech settings regardless of the application settings. 1 = override application settings, 0 = use application settings (if specified).

USB Mass Storage Enabled

If this setting is set (to anything), then all references to Gmail on the device must change to Google Mail.

The maximum number of times we will retry a connection to an access point for which we have failed in acquiring an IP address from DHCP. A value of N means that we will make N+1 connection attempts in all.

Maximum amount of time in milliseconds to hold a wakelock while waiting for mobile data connectivity to be established after a disconnect from Wi-Fi.

Whether to notify the user of open networks.

If not connected and the scan results have an open network, we will put this notification up. If we attempt to connect to a network or the open network(s) disappear, we remove the notification. When we show the notification, we will not show it again for WIFI_NETWORKS_AVAILABLE_REPEAT_DELAY time.

Delay (in seconds) before repeating the Wi-Fi networks available notification. Connecting to a network will reset the timer.

When the number of open networks exceeds this number, the least-recently-used excess networks will be removed.

Whether the Wi-Fi should be on. Only the Wi-Fi service should touch this.

The acceptable packet loss percentage (range 0 - 100) before trying another AP on the same network.

The number of access points required for a network in order for the watchdog to monitor it.

The delay between background checks.

Whether the Wi-Fi watchdog is enabled for background checking even after it thinks the user has connected to a good access point.

The timeout for a background ping

The number of initial pings to perform that *may* be ignored if they fail. Again, if these fail, they will *not* be used in packet loss calculation. For example, one network always seemed to time out for the first couple pings, so this is set to 3 by default.

The maximum number of access points (per network) to attempt to test. If this number is reached, the watchdog will no longer monitor the initial connection state for the network. This is a safeguard for networks containing multiple APs whose DNS does not respond to pings.

Whether the Wi-Fi watchdog is enabled.

The number of pings to test if an access point is a good connection.

The delay between pings.

The timeout per ping.

A comma-separated list of SSIDs for which the Wi-Fi watchdog should be enabled.

The content:// style URL for this table

Convenience function for retrieving a single secure settings value as a floating point number. Note that internally setting values are always stored as strings; this function converts the string to an float for you. The default value will be returned if the setting is not defined or not a valid float.

Convenience function for retrieving a single secure settings value as a float. Note that internally setting values are always stored as strings; this function converts the string to a float for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Convenience function for retrieving a single secure settings value as an integer. Note that internally setting values are always stored as strings; this function converts the string to an integer for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Convenience function for retrieving a single secure settings value as an integer. Note that internally setting values are always stored as strings; this function converts the string to an integer for you. The default value will be returned if the setting is not defined or not an integer.

Convenience function for retrieving a single secure settings value as a long. Note that internally setting values are always stored as strings; this function converts the string to a long for you. The default value will be returned if the setting is not defined or not a long.

Convenience function for retrieving a single secure settings value as a long. Note that internally setting values are always stored as strings; this function converts the string to a long for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Look up a name in the database.

Construct the content URI for a particular name/value pair, useful for monitoring changes with a ContentObserver.

Helper method for determining if a location provider is enabled.

Convenience function for updating a single settings value as a floating point number. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Convenience function for updating a single settings value as an integer. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Convenience function for updating a secure settings value as a long integer. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Store a name/value pair into the database.

Thread-safe method for enabling or disabling a single location provider.